Ford Truck Bed Covers

Why Does Your Ford Need a Truck Bed Cover?

Water, Snow, and Salt Wreck an Unprotected Bed

An open Ford bed collects every bit of standing water, snowmelt, and road salt it meets. That standing moisture sits against the sheet metal and rots out the wheelhouses, the tailgate seam, and the bed floor long before the rest of the truck shows rust. A sealed cover dams off that water at the rail and the tailgate edge so your cargo stays dry and the steel underneath gets a fighting chance.

An Open Bed Is an Open Invitation to Theft

Tools, tie-downs, and gear left in an open bed disappear the second you walk away. Soft tarps do nothing to stop a smash-and-grab, and a loose load can fly out on the highway and hurt the truck behind you. A locking hard tri-fold or retractable cover closes the bed off completely, so the only way in is through the tailgate lock.

Wind Drag, Flapping Tarps, and Flying Debris

A torn factory tarp flaps at speed, frays worse by the mile, and robs you of fuel economy while it shakes the bed. Loose cargo catches wind and shifts on every corner. A properly tensioned cover cleans up the airflow over the tailgate and locks your load down so nothing moves, flaps, or escapes.

What Can a Truck Bed Cover Solve?

Sealed Rail and Tailgate Edge

Weatherproof rubber seals along the side rails and the tailgate close the gaps where water and dust sneak in. The result is a dry, clean bed for tools, groceries, and luggage, even through a cross-state rainstorm.

Tension System That Holds at Highway Speed

Industrial-strength hook-and-loop and cam-lock tension keep the cover drum-tight from the bulkhead to the tailgate. No flapping, no ballooning, no torn seams after a season of towing.

Full-Bed Access When You Need It

Roll-up panels strap out of the way in seconds and tri-fold covers stack forward against the cab. You keep full bed length for lumber, furniture, and bulky loads, then seal it back up just as fast.

Stainless Clamp-On, No-Drill Hardware

T304 stainless steel brackets clamp onto the factory bed lip with no drilling or cutting. Install takes one person and a few hand tools, and the whole setup removes cleanly if you trade the truck.

Shop Ford Truck Bed Covers by Vehicle & Fitment Guide

• 6.5 Ft Short Bed Soft Tri-Fold Tonneau Cover - Fits the Ford F-150, F-250, and F-350 with a 6.5 ft standard bed (1973-1996). Marine-grade vinyl over aluminum support bows with stainless clamps, folds forward in three panels for quick access, and seals the tailgate edge against rain and salt.
• 8FT Long Bed Roll-Up Tonneau Cover - Fits the Ford F-250 and F-350 Super Duty 8 ft long bed (1999-2016). Heavy vinyl over powder-coated aluminum slats with T304 stainless hardware, rolls up tight for full bed access, and clamps on with no drilling.
• Ford F-150 (2015-2020, 13th generation) - Measure for a 5.5 ft SuperCrew bed or a 6.5 ft SuperCab bed and choose a hard tri-fold for locked security or a soft roll-up for full bed access.
• Ford F-150 (2021-present, 14th generation) - Confirm your 5.5 ft or 6.5 ft bed length before ordering, since the new body style uses the same rail geometry; a retractable or hard tri-fold covers the daily-driver security need.
• Ford F-250 and F-350 Super Duty (2017-present) - Match your 6.75 ft or 8 ft bed length; the 8 ft roll-up cover is the workhorse choice for towing and jobsite hauls.
• Ford Ranger (2019-2023) - Built on a 5 ft bed, so size a low-profile tri-fold or roll-up cover to that shorter box and confirm the next-generation 2024+ Ranger separately.
• Ford Maverick (2022-present) - Runs a 4.5 ft bed, so match a compact soft folding or hard roll-up cover built specifically for the Maverick bed length.

Why Choose EGR Performance?

The industry standard for high-performance diesel reliability.

Premium Quality & Rigorous Testing

Our EGR, DPF, and CCV delete kits are engineered from premium-grade materials and subjected to brutal quality control and field testing. Unlike generic alternatives, our products are built to withstand extreme heat and pressure, delivering unmatched durability and long-term stability when your rig needs it most.

20 Years of Proven Diesel Expertise

We aren't just selling parts. We live in this industry. With two decades of hands-on experience providing specialized modification solutions for heavy-duty truck owners, our upgrades have been extensively proven across every driving environment, from daily towing to high-performance tracks.

Industry-Leading Standards

We work hand-in-hand with top-tier industry partners and reputable organizations. Every product we design, test, and ship meets or exceeds strict industry standards, ensuring your Powerstroke, Cummins, or Duramax gets the exact precision it deserves.

Real Results, Proven Track Record

Thousands of diesel owners trust us to unlock their engine's true potential. Our massive library of positive customer feedback and successful build case studies proves one thing: our kits deliver real horsepower, lower EGTs, and flawless reliability in the real world.

What is the best type of Ford truck bed cover for an F-150?

It comes down to how you use the bed.
A hard tri-fold tonneau cover gives you the best security and weather sealing for daily gear storage, since the rigid panels lock and the rubber rail gaskets shed water.
A soft roll-up tonneau cover is lighter, more affordable, and rolls completely out of the way for full bed access when you haul lumber or furniture.
A retractable tonneau cover rolls into a canister for maximum access with a lock, but it eats roughly a foot of bed length and costs more. For most F-150 owners, a hard tri-fold on a 5.5 ft or 6.5 ft bed hits the sweet spot between security, weather protection, and price.

Are these Ford tonneau covers waterproof and weather-sealed?

No cover is 100 percent waterproof, but ours are engineered to be highly water-resistant.
The marine-grade vinyl stretches tight over aluminum support bows, the rails clamp down with weatherproof rubber tailgate seals, and the seams are double-stitched to fight off road spray and standing rain.
Expect a few drops around the tailgate corner in a driving storm, which is normal for any cover on the market, but your tools and cargo stay dry through everyday weather and washouts.

Which bed size do I need for my Ford F-150 tonneau cover?

Measure your bed length from the inside of the bulkhead to the inside of the tailgate, and do not guess from the cab configuration.
F-150 SuperCrew models usually run a 5.5 ft bed, SuperCab and many Regular Cabs run a 6.5 ft bed, and long-wheelbase Regular Cabs run an 8 ft bed.
Ordering the wrong length is the number one reason covers get returned, so match the measurement to the cover exactly before you buy.

Will a tonneau cover improve my Ford truck's gas mileage?

It can, but do not expect a huge jump.
A sealed cover cleans up the airflow over the tailgate, and a few owners report a small mileage improvement on the highway.
The bigger, more reliable gains come from protecting your cargo, cutting wind noise, and keeping the bed clean, not from fuel savings. Treat any mileage bump as a bonus, not the main reason to buy.

How hard is it to install a Ford truck bed cover, and do I need to drill?

Most of our covers are a no-drill, clamp-on install that one person can finish in 20 to 45 minutes with basic hand tools.
The rails clamp onto the factory bed lip with stainless steel brackets, the seals seat along the tailgate edge, and the tension is set with the hook-and-loop or cam locks.
No cutting or drilling into your bed is required, and the whole assembly comes back off cleanly if you ever trade the truck in.

What fits the 1999 to 2016 Ford F-250 and F-350 Super Duty long bed?

Our 8 ft Long Bed Roll-Up Tonneau Cover is built specifically for the 1999 through 2016 Ford F-250 and F-350 Super Duty long bed.
It uses heavy marine-grade vinyl over powder-coated aluminum slats with T304 stainless steel hardware, rolls up tight for full bed access, and seals along the tailgate to keep rain and salt out of your tools during cross-country towing.

Is there a cover for older Ford F-150, F-250, and F-350 trucks from 1973 to 1996?

Yes.
Our 6.5 ft Short Bed Soft Tri-Fold Tonneau Cover is engineered for the 1973 through 1996 Ford F-150, F-250, and F-350 with a 6.5 ft standard bed.
It uses a marine-grade vinyl skin over aircraft-grade aluminum support bows with industrial-strength hook-and-loop tension, folds forward in three panels for quick bed access, and clamps on with stainless hardware so you do not drill into a classic truck.

Can I drive with the tonneau cover open or partially folded?

Yes.
A soft roll-up cover rolls all the way to the bulkhead and straps in place so the bed is fully open for tall loads.
A tri-fold cover folds forward panel by panel and secures with buckles or straps, letting you haul oversized cargo while the folded section stays locked down. Just make sure the folded or rolled section is strapped tight before you hit the highway so it does not catch wind.

Do these covers lock, and how secure are they against theft?

Hard tri-fold and retractable covers lock with keyed hardware, so once the tailgate is shut the bed is closed off to a smash-and-grab.
Soft roll-up covers use tension and clamps and are better for weather and quick access than high security, since vinyl can be cut.
If protecting expensive tools or gear is the priority, lean toward a locking hard cover rather than a soft roll-up.

Are Ford truck bed covers street-legal, and what is the shipping, warranty, and return policy?

Ford truck bed covers are street-legal, DOT-accepted accessories in all 50 states, not emissions or off-road delete parts, so there are no legality concerns about running one on your daily driver.
The one thing to get right is fitment: measure your bed length and confirm your model year before ordering, since a mismatched size is the main reason covers get returned.
Every cover includes free shipping from our U.S. warehouse, is backed by a 1-year warranty against defects, and comes with our 45-day return policy so you can order risk-free.